Adding a new event

Content:

Event based on data.

To add a new event based on the data, take the following steps:

1. Go to the Events section.

2. Click Add new Event.

3. Select the “Event based on the data” in the General Information tab. Enter “Name” and “Description” of the event. (Field Descriptionis not required to fill in). 4. Select the following In the “Event Condition” tab:

  • the device for which the event is being created;
  • select the type of messages;
  • select a device parameter (Input), by which the event condition is created;
  • select event condition:
    • more (>) means that the event will trigger if the parameter received from the device is greater than the value specified in the condition;
    • less (<) means that the event will trigger if the parameter received from the device is less than the value specified in the condition;
    • equal to (=) means that the event will trigger if the parameter received from the device is equal to the value specified in the condition;
  • enter the condition value for the selected parameter;
  • click the Save conditions.

Several conditions can be set for one device. To do so, click Add condition button, fill it in and save it. The dependence of the conditions relative to each other is regulated by and/or parameter:

  • And means that for the event to be triggered all the conditions must be met;
  • Or means that one of the conditions must be met for the event to be triggered.

5. Notification:

  • set the notification repeat switch to the desired position:
    • Smart repetition means that after the event is triggered, the notification is sent once until the event cycle ends;
    • Once means that after the event is triggered once and the notification is sent, the event is deactivated;
    • Repeat means that a notification is sent every time an event is triggered (every 10 seconds).
  • select Notification Type (Voice Notification, SMS Notification or Email Notification);

To receive Voice messages and SMS, you need to register in the SMS center, top up the balance and activate the integration with the SMS center in “Company settings” of the system.

  • enter Phone (for Notification via SMS or Voice notification) or Email address (for Notification via Email);
  • enter the text of the message.

6. Press Create an event button.

Event based on lack of activity.

1. To add a new event based on the lack of activity, take the following steps:

  • Go to the “Events” section.
  • Click “Add” new “Event”.
  • Select the type of event based on the lack of activity. Then enter the “Name” and the “Description” of the event (“Description” field is optional) in the General Information tab.

2. Select the following In the “Event Condition” tab:

  • select a model. If it is necessary for the event to be distributed to all devices of this model, it is necessary to put a check mark next to the corresponding option.
  • select device name
  • specify the timeout time (the delay in triggering the event when the device is not active). The field is optional.

3. Notification:

  • set the notification repeat switch to the desired position:
    • Smart repetition means that after the event is triggered, the notification is sent once until the event cycle ends;
    • Once means that after the event is triggered once and the notification is sent, the event is deactivated;
    • Repeat means that a notification is sent every time an event is triggered (every 10 seconds).
  • select Notification Type (Voice Notification, SMS Notification or Email Notification);

To send Voice and SMS notifications in the “Сompany settings” you need to specify your credentials of the SMS center through which the sending of the Voice and SMS notifications will be carried out.

  • enter Phone (for Notification via SMS or Voice notification) or Email address (for Notification via Email);
  • enter the text of the message.

4. Press Create an event button.

Event on “Balance group”.

1. To add a new event for the “Balance group”, you must:

To create an event for a balance group, you must first create it, you can read the article on the balance group at the link.

  • Go to the “Events” section.
  • Click the “Add new event” button.
  • In the “General Information” tab, select the event type “Events by balance groups”, enter the “Name” and “Description” of the event. (The “Description” field is optional).

2. In the “Event condition” tab:

  • select from the list “Balance group” for which “imbalance” will be monitored.

3. In the “Notification” tab:

  • select the number of repetitions of the notification:
    • Smart repeat – after the event is triggered, the notification is sent once, without repeats, until the event cycle ends;
    • Once – after a single triggering of the event and sending a notification, the event is deactivated;
    • Repeat – the notification is sent every time the event is triggered (once every 10 seconds):
  • select Notification type (Voice notification, Notification via SMS or Notification via Email);

To send Voice and SMS notifications in the company settings, you must specify your credentials of the SMS center through which Voice and SMS notifications will be sent.

  • enter Phone (for Notification via SMS or Voice Notification) or Email Address (for Notification via Email);
  • enter the text of the message.

4. Press the “Create event” button.

   Send article as PDF